Acorn stairlift repair and fault codes
Most Acorn stoppages are the lift protecting itself rather than breaking down. Here is every display code, grouped by whether you can clear it yourself.
Last verified
First, work out which code system you have
This is where most advice goes wrong. Acorn does not use one set of codes. Which list applies to your lift depends on the model and on the circuit board fitted, so a code table from the wrong generation will tell you the wrong thing.
- A single character that sits there without alternating, such as just a number, points to an older board generation.
- Two characters alternating, such as a letter then a number, points to a later board.
- Straight lifts (the Superglide 120 and 130 families, also sold as Brooks) and curved lifts (the 80 and 180) use different sets again.
Find the model number on the label on the carriage before you look anything up. If the lift was bought second hand or the previous owner left it behind, that label is often the only record of what you actually have.
The codes, and what each one means
The table below is the digital display code set published in Acorn's user manual for the Superglide 130 straight stairlift. Curved models, and older board generations, use different codes. If yours shows something not listed here, that is the likely reason.
Acorn splits the codes into groups, and the group matters more than the code. The first two groups mean the lift is working. The last three mean it has stopped.
C codes: charging. The lift works normally
| Code | Meaning | What to do |
|---|---|---|
| C1 to C5 | Charging. C1 is nearly empty, rising to C5 as it fills | Nothing. Leave it on the charge point |
| C6 | Fully charged | Nothing |
| C7 | Charging voltage too low | Call a technician |
| C8 | Charging voltage too high | Call a technician |
| C9 | Battery fault: charger connected but the battery is missing or failed | Call a technician |
A codes and a blank screen: normal operation
| Code | Meaning | What to do |
|---|---|---|
| Blank | Asleep, or no power reaching it | Check the battery isolation switch is on, then move the paddle to wake it |
| A1 + beeping | Parked off the charge point, so it is not charging | Drive it to a charge point. Check the mains is on |
| A2 / A3 | Travelling up or down on the armrest control | Nothing |
| A4 / A5 | Travelling up or down on the remote | Nothing |
| A9 | Working the hinged section of rail | Let it finish |
A1 with a beep is the code people panic about, and it is the least serious one on this page. The lift has been left somewhere other than a charge point.
E codes: it has stopped, and you can usually fix it
| Code | Meaning | What to do |
|---|---|---|
| E1 | Footrest sensor triggered going down | Clear whatever is under the footrest |
| E2 | Footrest sensor triggered going up | Clear the obstruction |
| E4 | Carriage sensor triggered going down | Clear the obstruction on the stairs |
| E5 | Carriage sensor triggered going up | Clear the obstruction on the stairs |
| E6 | Seat is not locked in the riding position | Swivel the seat back to face forward |
| E7 | Battery low. It will not travel up | Drive it down to a charge point and leave it |
| E9 | Key switch is off | Turn the key on |
Every E code is the lift refusing to move for a reason it can see. None of them means the lift is broken.
H and F codes: technician territory
| Code | Meaning | What to do |
|---|---|---|
| H1 / H2 | A safety circuit is grounding to the chassis | Technician. Each switch in the circuit has to be tested |
| H3 | Cannot communicate with the hinge | Check the mains is on and plugged in, then call |
| H6 | Hinge did not reach its end position | Check for obstructions around the hinge, then call |
| F1 | Relay fault | Power off for 30 seconds. If it returns, call |
| F2 | Brake fault | Power off 30 seconds, then charge on a charge point for an hour. If it returns, call |
| F3 | Motor drawing too much current | Power off for 30 seconds. If it returns, call |
| F5 | Battery flat, with an audible alarm | Press the arm control or remote once to silence it, then drive down to charge |
| F6 | Travelled past the final limit | Hand wind it back. See the manual for the winding point |
| F7 | Overspeed governor has tripped | Hand wind the lift upward to reset the governor |
F6 and F7 involve hand winding, which is a documented procedure in the manual with a specific access point on the carriage. Read that section before attempting it rather than improvising.
The five things to check before calling anyone
- Is it parked on a charge point? An Acorn charges only when the carriage is sitting at a charge point, not merely at the end of the rail. This is the single most common cause of a lift that has gone dead.
- Is the mains still on? Check the transformer is plugged in, the socket is switched on and the breaker has not tripped. A vacuum cleaner unplugging the charger is a genuinely common story.
- Is the key turned on?
- Is anything against the footplate or under the carriage? Shoes, a stair rod, a rug edge, a pet toy. The sensors are deliberately sensitive.
- Is the seat locked straight? Most models will not drive with the seat swivelled, because that is what stops the chair moving while someone is getting on.
If all five check out and the code persists, stop there. The batteries, the charger transformer, the control board and the safety switches are not owner serviceable parts, and the lift carries someone up a staircase.
If Acorn did not install it, or has moved on
A large number of Acorn units in American homes are now orphaned: bought by a previous owner, inherited with the house, or installed by a dealer who has since closed. The question then is not what the code means but who will come out.
Other brands work differently: see Harmar, which uses lights and beeps rather than a numeric display.
Independent stairlift technicians routinely service brands they did not sell, and plenty carry Acorn parts. Others will only touch what they installed. Almost no one says which on their website, so ask it first: will you service an Acorn you did not install? Our directory lists the brands each provider installs, which is the best public signal of who already stocks the parts.
When you call, have ready: the model, the code showing, whether it alternates, and whether the lift is parked on a charge point. That is most of a phone diagnosis, and it is sometimes enough to resolve the problem without a visit.
Repair or replace
Batteries are a consumable and will need replacing during the life of the lift. Beyond that, weigh a repair quote against what a replacement costs. A refurbished straight lift can be close to the price of a major repair on an old one. A curved lift is a different calculation entirely, because the custom rail is the expensive part and it usually stays.
Codes and remedies above are taken from Acorn's own user manual for the Superglide 130 and reworded here. Checked on the date shown. Curved models and older circuit boards use different code sets, so if a code on your lift is not listed, check the manual for your specific model rather than assuming the nearest match.